Hardwood Flooring

Hardwood Flooring Installation in Hampton Roads

We install solid and engineered hardwood floors. Every job starts with a moisture reading of the subfloor and the boards, because wood swells and shrinks with the air around it.

5.0
Empty living room with new wood-look vinyl plank flooring
Finished kitchen with white cabinets and gray counters, ready for move-in

Solid and engineered

Before and after

The same room, with a new wood floor

The walls, the window and the trim stay. The worn floor comes out, the subfloor is checked and new boards go down.

Comes out
The old floor, down to the subfloor
Gets checked
Subfloor: flat, dry, solid and quiet
Goes in
New boards, trim put back or replaced
Illustration, before: a room with a worn, stained wood floor; after, the same room with a new oak hardwood floor
Illustration. Drag the handle to compare.

Compare

Solid or engineered?

Both are real wood on top, and once they are down they look the same. What is under the top layer decides where each one belongs.

Solid hardwood

One piece of wood, top to bottom.

What it is
Boards milled from a single piece of oak, maple, hickory or walnut.
How it goes down
Nailed or stapled to a wood subfloor.
Humidity
Moves more as the seasons change. It needs steady indoor air.
Refinishing
Can be sanded and refinished several times over its life.
Best when
The house sits on a crawl space or has wood subfloors, and you want a floor for the long run.

On a slab

Engineered hardwood

A hardwood top over a layered core.

What it is
A real hardwood layer bonded to plies that run in crossing directions.
How it goes down
Glued, nailed or floated, so it fits more subfloors.
Humidity
Steadier when the air turns humid, which helps near the coast.
Refinishing
Depends on how thick the top layer is. Ask before you buy.
Best when
The house sits on a concrete slab, or the room sees bigger swings in humidity.

Neither belongs in a full bathroom. For wet rooms we point you to tile or vinyl plank.

Layouts

Pick how the boards run

The same wood reads very differently depending on the layout. Pick one to see it on a floor.

Drawing, not to scale

StraightBoards run the length of the room with staggered ends. The classic look, the least cutting and the least waste.

Patterns take more material and more time than a straight lay. We tell you how much before you choose.

Species

How hard is each wood?

The Janka test measures the force it takes to press a steel ball into the wood. A higher number means fewer dents from heels, chairs and dog claws.

  • 1,010lbf

    Black walnut

    Rich and dark. The softest of the five, so it suits bedrooms and quieter rooms.

  • 1,290lbf

    Red oak

    The benchmark other floors are compared with. Takes stain evenly.

  • 1,360lbf

    White oak

    A little harder than red oak and steadier around moisture. Today’s most requested look.

  • 1,450lbf

    Hard maple

    Pale and smooth with a fine grain. Shows less grain pattern, more of the finish.

  • 1,820lbf

    Hickory

    The hardest of the five, with strong colour variation from board to board.

Janka values in pounds-force, from the USDA Forest Products Laboratory. The finish matters as much as the species for scratches.

How it is built

What a hardwood floor sits on

A wood floor is only as good as what is under it. These are the parts, from the framing up.

Illustration of a hardwood floor taken apart: floor joists, plywood subfloor, black felt underlayment, oak boards with flooring nails and a white baseboard Joists The framing that carries the floor. Bounce or sag here shows up later as squeaks and gaps. Subfloor Plywood fastened tight to the joists. It has to be flat, dry and solid before any board goes down. Underlayment Felt or a similar layer between subfloor and boards. It slows moisture from below and quiets the floor. Hardwood boards Tongue-and-groove boards, left in the house first so they settle to its air. Fasteners Flooring nails or staples driven through the tongue, so none show on the surface. Baseboard Covers the gap left at the walls. That gap lets the floor swell in summer without buckling.

Flooring

Other floors we install

Not every room suits wood. See what goes where.

All services

Near the coast

Wood and Hampton Roads air

Humid summers and damp crawl spaces are the main reasons wood floors fail here. This is what we check before a board is nailed.

  1. Moisture readings

    We meter the subfloor and the boards. Strip flooring should be within 4 percent of the subfloor, wider plank within 2.

  2. Acclimation

    The boards sit in the house, with the air conditioning running, until their readings settle.

  3. The crawl space

    Standing water or a missing vapor barrier under the house will cup a new floor. We look before we quote.

  4. Indoor air

    Wood stays calm when the house is kept between 30 and 50 percent relative humidity through the year.

FAQ

Questions about hardwood floors

Can hardwood go over a concrete slab?

Engineered hardwood can, glued or floated over a slab that has been tested for moisture. Solid hardwood needs a wood subfloor.

Can my old wood floor be refinished instead of replaced?

Often, if the boards are solid, dry and thick enough to sand. If that is all your floor needs, we will tell you so at the estimate.

Why do the boards have to sit in my house first?

Wood takes on and gives off moisture until it matches the air around it. Boards installed before that happens shrink or swell afterward, and that is where gaps and cupping come from.

Is hardwood a good idea in a kitchen?

It can be, with a durable finish and spills wiped soon. In a full bathroom or a laundry room we recommend tile or vinyl plank instead.

Which species holds up best with dogs?

Harder species such as hickory and white oak dent less, and a matte finish hides scratches better than a glossy one.

Do you move the furniture?

Tell us what is in the rooms when we visit and we will plan for it in the estimate.

Free in-home estimate

Ready for a new floor?

We will measure the rooms, check what is under the floor you have and give you a detailed estimate at no cost.